673N Contitech Bus Air Spring W01-095-0198 Firestone Rubber Air Bellows Volvo 1611776

Product Description

Cross Reference Number

Cross Firestone W01-095-0198 / W01 095 0198 / W010950198

Cross Firestone 1R1A370285

Cross Contitech 673N

Cross Goodyear 9051

Cross Phoenix 1F21A

Cross Taurus B 141

Cross CF Gomma: 1S 285-022

Manufacturer Number

INBUS: 5001098

VAB HOOL: 624319-860

MEICEDES BENZ: 337.327.0001

MEICEDES BENZ: 383.327.0001

DAF/VDL: 0627854

VOLVO: 1611776

How to Install a Bus Airbag
1. Remove the old air spring
Remove the load
Jack up the bus frame to ensure that the suspension is fully extended and the air spring is depressurized.
Place the support frame in a stable position on the axle or chassis.
Relieve air pressure
Before disconnecting the air line, release the residual air pressure in the spring through the exhaust valve.
Mark the line connection position (for easy reinstallation).

2. Remove the fixing parts
Remove the upper and lower air spring fixing bolts/nuts (impact wrench may be required).
Carefully remove the old spring and check the seat and piston for rust or damage.

3. Install the new air spring
Inspect the new spring and seat
Clean the mounting surface to ensure that there is no debris or rust.
Confirm that the new spring model is the same as the old one (such as height, load-bearing class).
Positioning and installation
Align the new air spring with the upper and lower mounting seats (note the direction mark).
Temporarily tighten the fixing bolts by hand to ensure that the spring is centered.
Connect the air line
Reconnect the air pipe and use a new clamp or seal to prevent air leakage.
Make sure there are no twists or bends in the pipes.

4. Inflation and testing
Preliminary inflation
Start the bus air system (or external air source) and slowly inflate to the recommended pressure (refer to the manual).
Check all joints with soapy water for bubbles (leakage needs to be resealed).
Adjust the height
If the bus is equipped with an automatic leveling system, observe whether the body is level after starting.
For manually adjusted models, measure the wheel arch height to ensure left and right symmetry.
Tighten the bolts
Tighten all bolts to the manufacturer's specifications with a torque wrench at the correct pressure (avoid over-tightening to damage the rubber).

5. Final inspection
Road test: Test the shock absorption effect at a low speed and listen for any abnormal noise.
Recheck: Check the air pressure and leaks again after parking.
System calibration (if applicable): Some electronic suspensions need to be reset with a diagnostic tester.

The Real Picture: GUOMAT 673N Bus Air Suspension

Guangzhou Guomat Air Spring Co., Ltd. is located in Guangzhou, about 15min’s drive from Baiyun Airport. Our mainly products are air spring, rubber bellows, air suspension spring, air suspension compressor and refitted suspension system. They are widely used in bus, truck, cabin, vehicles’ seat, luxurious car and industrial machine field.

GUOMAT Factory gate：

Established in 2008, Our company covers 20,000㎡ and is located in Taihe Town Baiyun District. With the rapid development of our company, we are equipped with modernized workshop and advanced rubber air springs equipments now. We are the first company who started air spring business and has become one of the largest air spring manufacturing bases in China.

In 2017, we launched a collaboration with High Tech of US customers to customize the products of our customers and the logo of our customers. Every year, there are about 10,000 orders. In continuous cooperation, the products meet the international inspection standard ISO/TS16949:2009, and the customers are very satisfied with the products produced. This is our high recognition from American customers and also gives us Great motivation.

In 2018, we started cooperation with German GmbH, mainly industrial air springs, which are suitable for industrial equipment. We have successfully developed and produced the natural air-seal of the skin to reach the 700mm flanged air spring, the customer's annual demand is a few hundred.

With the development of business and demand for customers, our company introduced business with TomLog Corporation in 2010, our strategic cooperative partner in Taiwan. Then we developed air compressor program and air spring related business, in 2015, America Goodyear Corporation met with the transfer of shares in the North American plant, our company was granted with sale agent for air springs in China, providing more choice for our customers. Our company adopts the most advanced domestic air spring processing equipment and international production technology. Combined with unique production process, our company strictly execute international standards for production and spare no efforts to create the world-class products. We will endeavor to make air spring widely used at home and abroad, and let more and more customers to enjoy the best damping effect.